Dear Sir or Madam, good morning!Colored epoxy resin 6 kg + HARDENER 2 kgEpoxy resin ratio (ingredient A) of hardener (component B) 3:1 wagowoATTENTION: The colors presented here are for illustrative purposes only and may differ slightly from reality. The appearance depends e.g.. from the monitor settings.
Epoxy paint for metalDescription: two-component, high-build, anti-corrosive epoxy paint with a polyamine hardener and low solvent content. Intended use: intended for use as a topcoat in epoxy coating systems resistant to mechanical loads and chemicals, and in a protective coating system. The paint has good adhesion to refined zinc, aluminum, thin-layer steel, and acid-resistant steel.. The paint creates a thick, chemically resistant coating. The coating is suitable for interior and exterior surfaces, as well as for underground and submerged steel structures. Properties: it has excellent adhesion to steel, galvanized and aluminum surfaces. Apply at a temperature of at least +10°C.TECHNICAL DATA:Composition: epoxy resins, polyamine hardener, aromatic solvent, fillers, pigments, contamination modifiers.Drying time at 20±2°C: due to lack of extrusion - 12-48 hours, the next layer can be applied after 15 hours, subject to maximum load after a week. Drying time increases with decreasing temperature, increasing relative air humidity and depends on the consumption (layer thickness) paints.Material consumption:in 1 layer: 0.18-0.22 kg / m2w 2 layers: 0.24-0.27 kg / m2 depending on the surface and application methodSolvent: silicone XApplication method: spray, Brush, Roller, immersion, marking machineDensity, g / cm3: 1.5±0.05Mass fraction of non-volatile substances,%: 86±3 depending on the colorGloss level: semi-matte (85 GU at a measurement angle of 60°)Instructions for use: the surface must be dry. During the application and curing of the paint, the air temperature should not fall below +10ºC. The relative humidity of the air should not exceed 80%. When working on large areas and/or for a long time, the paint should be mixed periodically. It is not recommended to keep the container with open products for a long time. Do not apply paint in direct sunlight, strong wind, or atmospheric precipitation. After application, the coating should not be exposed to atmospheric precipitation for 12 hours.. Appearance, coating quality, and lifespan depend primarily on the care taken in preparing the surface.. The surface should be thoroughly cleaned of dirt, dust, grease, old paint coatings, and traces of microbiological contamination.. Shot blasting is recommended. If this is not possible, clean the surface of dirt, dust, grease, and other contaminants. Rust and scale should be removed using a scraper, wire brush, or other convenient method. Matte the surface with fine-grit abrasive material. Degrease with solvent. It is best to use the product within its shelf life within 2 hours. Apply with a brush, roller, or sprayer in 1-2 coats to a dry, clean surface, avoiding streaks, as the dry film thickness of the paint on the entire surface should be at least 80 microns., on a primed surface and 120 µm.. on the surface without primer. Precautions: avoid contact with skin, use personal protective equipment. The product contains a solvent, therefore effective ventilation must be ensured.
Colored epoxy resin for use as a fine-layer coating or for painting on concrete surfaces to create a wear-resistant, chemical-resistant, and attractive finish. Cured coatings have very good mechanical resistance. (hardness, flexibility, abrasion resistance, impact strength) and chemical (see product technical sheet).The set comes with a hardener. Features:Extremely wear-resistant, applied to concrete, chemically resistant coating. Not afraid of butter, gasoline, and heavy loading equipment. Advantages of colored epoxy resin as paint:-High wear resistance;-Beautiful appearance;-Chemical-resistant;Can be used on:industrial floor, pharmaceutical floor, medical and food premises, cold storage rooms, floors with high traffic and utility load for public use, petrol stations, car washes, warehouses, workshops (including flooring for logistics centers).Color: grey, other colors see below.Drying time: 24 hours (one day) o thickness up to 1 mm at temperatures above 25°C. Surface preparation and application: Apply to a previously clean, dry floor. Prepare the paint for application by thoroughly mixing the components with a whisk on a drill in the proportions indicated on the packaging. The pot life of the mixed resin is preferably no more than 25 minutes.. Apply the material with a roller or squeegee in an even layer. It is possible to apply 1 thin layer, 2 thin layers with intermediate drying within 24 hours, or 1 thick layer up to a thickness of 1 mm.
PROPERTIES: Possibility of obtaining smooth decorative surfaces High surface aesthetics Mechanical resistance Chemical resistance Waterproofness Ease of cleaning
Hardening:Curing at room temperature should be carried out for 7 days to achieve full mechanical strength and for 14 days to achieve chemical resistance.. During application, prepare small portions of the composition that will be used within a few minutes. The optimal working conditions are 20°C and relative air humidity up to 65%.. It is not recommended to lay floors at temperatures below 15°C. At higher humidity, clouding, cratering, and tackiness may occur on the cured coating.. A particularly critical impact on the appearance and quality of the coating is caused by lowering the substrate temperature below the dew point temperature during curing.. In the case of applying multi-layer coatings, the next layer must not be applied if the substrate temperature is lower than or equal to the dew point temperature.
No-delivery refund
