Function : Decorative,Explosion-Proof,Heat Insulation
Model Number : 30/45/60/75/90 x 200/300/500 Cm
Surface Treatment : Embossed,Frosted / Etched,Opaque
Type : Glass Films
Feature : Self-Adhesive
Material : PVC
Origin : China
Item type : window glass film stickers foil tint paper cover Decals
Item size : 30/45/60/90 cm x 200/300/500 cm
Material : HTV heat transfer vinyl
Features 1 : Safety film / Solar film / Frosted film / sun blocking film
Features 2 : With Glue Self adheisve Film
Features 3 : thermal insulator / removable / privacy / sun protection
Applicable location : kitchen / furniture / home / slide doors / bathroom / house
function : Privacy Protection / home decoration
BUNPIG Clear Water Window Film
BUNPIG Frosted Window Film is designed to give a beautiful appearance of modern appearance to your windows and doors, whether for privacy, to block out an unsightly view or for decorative purposes. Besides prevent UV rays, it can also cut out a large proportion of the unwanted glare, whilst still allowing natural light to pass through. It will work on any smooth glass surface and can be used anywhere in the home, requires no additional cleaning and can be installed at a fraction of the cost.
SPECIFICATIONS:
Type: 2D Window Film
Material: Vinyl + PVC
Environmental: Through Europe EN71-3 standard and SGS
Thickness: 0.214 mm (excluding the backing film)
Average life: 3 years
Package Content: 1 roll of Window Film and 1 Piece of Installation Guide
HOW TO INSTALL THE BUNPIG WINDOW FILM?
3 TIPS BEFORE YOU START:
A small utility knife with breakaway blades is the best tool for trimming film. Film can dull a blade edge quickly; and a dull blade can tear film.
Fill a spray bottle with a soapy water solution: to 1qt. bottled water, add 1/4 tsp of liquid soap. Avoid using concentrated or degreasing detergents. If you can't find proper liquid soap, the clean water is also OK for the solution.
Remove any caulk, paint or glue debris that may be stuck to the window.
8 STEPS OF THE INSTALLATION:
Measure and record the dimensions the target glass.
Clean the glass thoroughly.
Add 1+ inch on every side when cutting the film so you have excess film to trim away.
Peel off the backing liner.
Generously spray the soapy water both on the glass and the window film.
Place the film on the wet glass, adjust the position of the window film.
Using a plastic squeegee or card, begin squeegeeing the water and air out from under the film.
Trim excess material away with a VERY sharp razor or craft knife, leaving a 1/16" wide gap around the edges of the film.
Frequently Asked Questions:
1. How to deal with the air bubbles?
Use a hard plastique squeegee or any plastic card to squeegee air bubbles and water. If you find it's hard to get rid of the bubbles, uncover the window film, spray more water between the glass and the film and squeegee firmly again. Water will make it much easier to remove bubbles.
2. Why the film fall off after a while?
Please check if you have removed the liner, trimmed the edges or squeegeed excess water and bubbles.
Leave a 1/16" wide gap around the four perimeter edges of the film. This gap is essential for the proper thermal expansion of the glass and allows you to completely squeegee the water and air from under the film.The blade or the knife for cutting the film is not sharp, resulting in deformation at the edge of the film. NOTE: Film can dull a blade edge quickly; and a dull blade can tear film.
3. Can I remove the film at a later stage?
Absolutely. Our blackout film is removable and reusable. You can just simply peel the film off the glass in seconds with no mess.
4. How to peel off the backing liner?
All static cling films have a liner, but some are clear and hard to see at first glance. If you can't separate the liner from the film, place a piece of scotch tape on both sides of the sheet, fold the tape over to create tabs, and use the tabs to separate the two sides.
Product instructions
Dear buyer, you can use your mobile phone to scan the QR code below and watch the installation video. It can help you better.
