For DL1000 DL650 V-Strom GSX-r1000 R600 R750 SV650 GSF1250 Motorcycle 1-6 Level LED Speed Gear Display Indicator ECU Plug

Mounting: For Boulevard C50 2005-2010 For Boulevard M50 2005-2018 For Boulevard M90 2009-2010 For Boulevard C90 2005-2012 For Boulevard C109R/T 2008-2015 For Boulevard M109R/R2 2006-2010 For DL650 V-Strom 2004-2011 For DL1000 V-Strom 2004-2013 For GSF650 Bandit 2009-2010 For GSF1250 Bandit 2007-2010 For GSF1250 N/NA Bandit 2007-2009 For GSF1250 S/SA Bandit 2007-2016 For GSX1400 2004-2009 For GSX650F 2008-2010 For GSX-R600 2004-2005 For GSX-R750 2004-2005 For GSX-R1000 2003 For Intruder C800 2005-2010 For Intruder M800 2005-2015 For Intruder C1500 2005-2012 For Intruder M1500 2009-2015 For Intruder C1800R 2008-2015 For Intruder M1800R 2006-2010 For Intruder M1800R2 2008-2010 For RMX-450Z All Years For RM-Z250 (EFi model) All Years For RM-Z450 (EFi model) All Years For SV650 2003-2014 For SV1000 2003-2009 For VL800 Intruder Volusia 2005-2010 For VL1500 Intruder 2005-2012 For VLR1800 2008-2015 For VZ800 Marauder 2005-2015 For VZ1500 2009-2015 For VZR1800 2006-2010 Package List: 1 x Motorcycle Speed Gear Display Preface: Congratulations on your purchase of gear position indicator. It is the most advanced gear position indicator on the market today. This product will fit all fuel injected (fi) motorcycles that have onboard diagnostic system connector. This connector is referred to as "coupler select switch mode" in the manuals. Unlike other gear indicators available for your bike, this product plugs into the diagnostic connector. Makes the installation very simple. The unit reads data directly from the ECM, offering faster and more reliable readings than competitive products. The unit is fully automatic, there are no buttons and no "programming wire", the display will indicate all gears correctly when the ignition is on, the side stand is up and the engine stop switch is in the run position. Installation: Installation: Find the white 6-pole male diagnostic connector, usually near the ecm box. You may have a black cap, or a "dummy" female plug attached to it.For gsf650 bandit / gsf1250; under the right side frame cover abs model For dl650; behind the right side fuel tank cover for vl1500 / boulevard c90 / intruder c1500; behind the head cover of the left frame other models; under the seat (pilot or pillion) Remove the black cover or female plug from the dummy, and plug in the jxkj plug. route the cable to the mounting location. remove the green plastic from the back of the unit and mount the display. secure the cable with the supplied cable ties. The unit is fully functional after installation. No need for configuration. Problems solution. Disconnect the connector and check that the pins are broken, bent, or pushed out of position. And make sure all connections are good and the connector is fully seated. Make sure the ignition is on, the side mount is up, and the engine stop switch is in working position when you test the gear position indicator. If some gears are not indicated correctly, the position of the Switch gear is probably defective, modified, or a tre box is installed. If the gears indicated are correct except under hard acceleration or braking, there is interference with the bike and wiring and the ecm receives incorrect values from the sensor gear position. This model indicates the position of the gear as known by the Ecm. do not.