Kingdom of Car Wash Mall Crystal 50ml Sponge with Micro Cloth Coating Car Wash Supplies for Unpainted Plastic 699 (For Only)

Set contents: ・Mall crystal 50ml…1 bottle (approximately 8 plastic door malls) ・Coating sponge…2 pieces ・Basic cloth S…1 piece ・Others, instruction manual attached Bulk information / Name: Mole Crystal 50ml / Purpose: Coating agent exclusively for Mole / Capacity: 50ml / Liquidity: Neutral / Ingredients: Organosilane, aluminum chelate compound, n-hexane How to use [1] Rinse off dust, sand, mud, etc. with a strong stream of water. [2] Thoroughly wash with our Body Clean to ensure that no dirt remains. If there is water repellency, please remove the fat with our wax remover. If oil remains, the coating film may not adhere properly, resulting in white unevenness. [3] Dry the construction surface by thoroughly wiping it to ensure that no moisture remains. [4] Saturate our coating sponge with this solution and apply it as thinly as possible without dripping. *Before using the coating sponge, make sure to saturate the ends of the coating sponge with the solvent. [5] Before the liquid hardens, please wipe it completely with our basic cloth. If you don't wipe it enough, the coating may crack and become white and uneven. [6] Thoroughly check that there is nothing left to wipe, and the process is complete. ■Restore the original luster of the mall! ! This product ``Mall Crystal'' is an ultra-high hardness glass mold coating agent developed as a plastic recycling agent. Unlike general shine agents, this is a special product for mall care that restores the original shine of malls. Even ordinary owners can install it evenly, so you can use it with confidence. Conventional mold polishing agents return to their original white state after a while after application. However, this "Mall Crystal" forms a hard transparent glass film, so the effect lasts for a long time without losing its luster. It is only sold online and cannot be purchased at mass retailers. ■ No deterioration due to hard glass film formation! Most mall polishing agents, both commercially available and commercially available, use petroleum-based solvents. Since it is a petroleum-based solvent (similar to tire wax), it cannot escape oxidation. The coating film, which has deteriorated due to oxidation of petroleum-based solvents, washes away when it rains. Furthermore, the remaining coating agent will remain like an oil film, making the condition worse than before it was applied. ``Mall Crystal'' is a mold coating agent that forms an inorganic hard glass film that does not cause oxidation or deterioration, so there is no need to worry about such things. ■ One-time construction lasts more than 6 months! A mold coating agent that forms a glass film that does not cause oxidation or deterioration. Both gloss and water repellency last for more than 6 months with a single application. In addition, the hard coating makes it less likely to get scratched, and it also has a water repellent effect that will definitely make washing your car more enjoyable. Plastic molding that has lost its luster due to deterioration over time → After installation, the black luster can be restored. It has enough capacity to coat even cars with many unpainted plastic parts. □ Note - This product can only be used on relatively rough, unpainted plastic materials such as moldings and bumpers. It cannot be used on transparent materials such as door visors and headlights.・Cannot be applied to soft materials. The coat film may crack.・If a thick coat is applied in one application, cracks may occur after curing. - After applying, do not leave it unattended and be sure to wipe it off at the end. - If you install the product with water scale or other dirt still attached, the dirt will not come off later, so please remove the dirt before use.・As the coating film is extremely strong, even if the coating film cracks or stains are applied, it cannot be removed after curing.・Avoid using in the scorching sun, in places exposed to direct sunlight, or when the construction surface is hot.・Complete drying takes about 6 hours. During this time, it is strictly prohibited to get wet or drive. [Please read before purchasing] This product is a coating agent exclusively for unpainted plastics, but there are concerns that it may not be compatible with some car models and may cause unevenness. Before installation, please be sure to perform a test installation on an inconspicuous area before applying it to the entire part.